I finally got some paint on the housing. Three coats of gloss black engine enamel.
Metal fabrication shop located in Merlin Oregon. We specialize in Dodge and Ram truck, repair and modification. From lift kits and suspension to full blown frame off builds. We service and repair all major brands or truck as well as equipment. We offer onsite welding and troubleshooting. We also build headache racks, bed rails and flatbeds.
Sunday, April 19, 2015
Tuesday, April 14, 2015
Fuel system pt2
I replaced the lift pump today. I ditched the mounting hardware and went with 8-1.25 X 45mm studs, lock-washers and nylocks. I went in from the top removing the fuel filter. I removed the old one and tried to remove the fuel heater but it would not budge. I unplugged the fuel heater and installed the new pump, it was a PIA with the studs it would really suck to reuse the original bolts. I hooked everything back up and fired the truck up. It ran rough for about 10 seconds then it smoothed out. Since the over drive likes to pop out the second you let off the throttle I went ahead and installed a DNR customs TPS delete kit. It allows you to set the overdrive shift point manually. I set it to engage at 45mph.
Here is the link to a TPS delete I did on my 12 valve,
Monday, April 13, 2015
Fuel system nightmares
The starting issues with Eli's truck are not over. They were gone for a short time then returned with a vengeance. The truck would crank and crank and when it would finally fire up it would run extremely rough for about 20-30 seconds like there was air in the fuel. After a fair amount of running around I found Napa Auto parts carries diesel fuel line. I picke up 11 feet of 3/8" id rubber line (it was all they had). We lifted the bed up dump truck style to get to the fuel tank and bypassed the supply line. I put an inline filter near the motor and bypassed the fuel heater. After running to autozone to buy a hand held fuel transfer pump (I couldn't find mine) I pulled diesel though the new line and hooked the line straight to the lift pump. I primed the pump and started it up. The truck fired up on the first crank and was running smooth, the lift pump was leaking like a sieve though. Next up replace the lift pump...
Saturday, April 11, 2015
Axle pt 29
Some wire wheel action for the hub spinals as well as u-joint removal. I picked up new u-joints only to come home and find that one was missing a seal. After returning to the store i was informed that those were the only two in stock. So I took a 20 mile trip at 9:30 at night to another store to get the u-joint.
Sunday, March 29, 2015
Axle pt 28
Since I broke my 9/16" socket I purchased a set of 12 point impact sockets. A cheater on the end of the breaker bar did the trick and the bolts broke loose. After quite a bit of scraping and wire wheeling the hubs cleaned up nicely, I also cut off the "nub" protruding at the mounting surface of the hubs. After the hubs were thoroughly scrubbed with lacquer thinner they revived a coat of self etching primer followed by a couple coats of engine enamel.
Axle pt27
I drove out out the inner axle seals and ran rags soaked in lacquer thinner through the tubes until they came out clean. I used part of the locking hubs to evenly drive in the new seals with out damaging them. After I got them both in I re installed the carrier, driving it into place with a non marring dead blow mallet and bolted it back down.
1111Wednesday, March 25, 2015
Axle pt26
I tackled the pinion seal today. The 1-5/16 nut that secures the yolk was ridiculously hard to break loose, even after repeatedly soaking it with penetrating oil the last couple days. After quite a bit of cranking on the cheater bar (on the breaker bar) it finally came loose. I had originally bought a pinion seal from Ford for a 89 D60 since I thought my axle was an 89. Needless to say it didn't line up and I ran to Oriels before they closed and picked up pinion seal, inner wheel seals and yolk hardware. The new seal went is easy and everything went back together smoothly. I don't know how many pounds the pinion nut is suppose to be torqued to so I just tightened as tight as I could.
Subscribe to:
Posts (Atom)
